Download
Table of Contents > Air conditioning system > Removing and installing rear temperature flap control motor

VW Tiguan Heating & Air Conditioner ➜ Removing and installing rear temperature flap control motor

lk  
Tiguan 2016 ➤ , Tiguan RUS 2017 ➤  
Heating, air conditioner - Edition 06.2017  
Installing  
Install in reverse order of removal. Observe the following:  
Note  
Check.operation of flaps and hinge mechanisms.  
Make sure levers and shafts are properly fitted in the mounts.  
– Position control motor -2- on air distribution housing. Gear  
wheel -3- of control motor must engage in gear wheel -1- of  
temperature flap lever.  
The long tooth -4- must engage in recess -arrow- on actuating  
lever.  
Note  
If the gear wheels on the control motor and temperature flap  
lever do not align, rotate the receptacle in the control motor.  
If the bolts cannot be fitted, the control motor is not completely  
seated on the housing.  
– Switch on ignition.  
– Connect respective control motor to vehicle wiring harness  
and select a setting on operating and display unit to set control  
motor to desired position (e.g. middle position). Wait until con‐  
trol motor has moved to desired position and switch off ignition.  
– Route wiring harness so that it cannot come into contact with  
any moving parts (e.g. actuating arm on control motor).  
Note  
Rotate control motor until it reaches a convenient position for in‐  
stallation. The direction of rotation can be changed by changing  
polarities.  
– Read event memory and erase any entries displayed. Then  
perform “basic setting” ⇒ Vehicle diagnostic tester in “Guided  
Fault Finding” mode.  
– Check operation of heater and air conditioning system.  
Specified torques  
⇒ “5.1 Assembly overview - heater and air conditioning unit”,  
page 111  
4.7  
Removing and installing rear tempera‐  
ture flap control motor - V137-  
Special tools and workshop equipment required  
♦ Vehicle diagnostic tester  
Removing  
– Switch all electrical consumers off.  
– Switch off ignition.  
– Withdraw ignition key.  
90  
Rep. gr.87 - Air conditioning system  
theMANUALS.org  
Tiguan 2016 ➤ , Tiguan RUS 2017 ➤  
Heating, air conditioner - Edition 06.2017  
– Remove centre console ⇒ General body repairs, interior; Rep.  
gr. 68 ; Centre console; Assembly overview - centre console .  
– Remove bolt -2- from rear temperature flap control motor -  
V137- -1-.  
lk  
– Unscrew bolts -3-.  
– Separate connector -2-.  
– Remove rear temperature flap control motor - V137- -1-.  
Installing  
Install in reverse order of removal. Observe the following:  
Note  
Check.operation of flaps and hinge mechanisms.  
Make sure levers and shafts are properly fitted in the mounts.  
– Check operation of heater and air conditioning system.  
Specified torques  
♦ Assembly overview - centre console ⇒ General body repairs,  
interior; Rep. gr. 68 ; Centre console; Assembly overview -  
centre console  
4.8  
Removing and installing fresh air/air re‐  
circulation, air flow flap control motor -  
V425- with potentiometer - G644-  
⇒ “4.8.2 Removing and installing fresh air/air recirculation, air flow  
flap control motor V425 , RHD vehicles”, page 93  
4.8.1  
Removing and installing fresh air/air re‐  
circulation, air flow flap control motor -  
V425- , left-hand drive vehicles  
Special tools and workshop equipment required  
♦ Vehicle diagnostic tester  
Removing  
– Switch all electrical consumers off.  
– Switch off ignition.  
– Withdraw ignition key.  
4. Control motors  
91  
theMANUALS.org  
 

Need help?

If after viewing the owner's manual or service manual you still have some unresolved questions about the car VW Tiguan you can write to us using the link below, describing your problem in detail, we try to answer all questions.


Ask your question on the page - Support!