Tiguan 2016 ➤ , Tiguan RUS 2017 ➤
General body repairs, exterior - Edition 06.2017
2
Door components
⇒ “2.2 Assembly overview - window regulator”, page 119
⇒ “2.3 Assembly overview - door handle and door lock”,
page 120
⇒ “2.4 Removing and installing window regulatorlkmotor”,
page 121
⇒ “2.5 Removing and installing window regulator”, page 123
⇒ “2.6 Removing and installing inner door cover”, page 126
⇒ “2.7 Removing and installing striker pin”, page 128
⇒ “2.8 Removing and installing cap on door handle”, page 130
⇒ “2.9 Removing and installing lock cylinder”, page 135
⇒ “2.10 Removing and installing door handle”, page 139
⇒ “2.11 Removing and installing door handle bracket”,
page 143
⇒ “2.12 Removing and installing door lock”, page 145
⇒ “2.13 Removing and installing window channel”, page 150
⇒ “2.14 Removing and installing outer window slot seal”,
page 153
⇒ “2.15 Removing and installing inner window slot seal”,
page 155
2.1
Assembly overview - door components
Note
The illustrations show the left-hand side. The procedure for the right-hand side is basically the same.
2. Door components
117
Tiguan 2016 ➤ , Tiguan RUS 2017 ➤
General body repairs, exterior - Edition 06.2017
1 - Rear door
❑ Removing and installing
⇒ page 106
❑ Adjusting ⇒ page 109
2 - Inner window slot seal
❑ Removing and installing
⇒ page 155
3 - Stickers
❑ Diameter 32 and 40 mm
❑ If necessary, manufac‐
ture using commercially
available textile adhe‐
sive tape.
❑ Stickers must cover the
openings completely
4 - Dampers
❑ Self-adhesive
❑ Installing:
–
Cut to size if required,
250 mm x 160 mm Po‐
sition as shown in illus‐
tration.
–
Warm using hot air
blower - V.A.G 1416-
and push on to outer
door panel with force.
5 - Dampers
❑ Self-adhesive
❑ Installing:
–
Cut to size if required,
200 mm x 100 mm Po‐
sition as shown in illus‐
tration. Distance to next insulation 10 mm.
–
Warm using hot air blower - V.A.G 1416- and push on to outer door panel with force.
6 - Inner door cover
❑ Removing and installing ⇒ page 126
7 - Outer window slot seal
❑ Removing and installing ⇒ page 153
8 - Stickers
❑ Qty. 3
❑ 15 mm x 50 mm
❑ If necessary, manufacture using commercially available textile adhesive tape.
❑ Stickers must cover the openings completely
9 - Window channel
❑ Removing and installing ⇒ page 150
118
Rep. gr.57 - Front doors, door components, central locking
Tiguan 2016 ➤ , Tiguan RUS 2017 ➤
General body repairs, exterior - Edition 06.2017
2.2
Assembly overview - window regulator
lk
1 - Window regulator
❑ Removing and installing
⇒ page 123
2 - Hexagon nut
❑ Qty. 4
❑ 6 Nm
3 - Window regulator motor -
V14/V15-
❑ Removing and installing
⇒ page 121
4 - Bolt
❑ Qty. 3
❑ 3 Nm
5 - Clip
❑ For securing cable
2. Door components
119
Tiguan 2016 ➤ , Tiguan RUS 2017 ➤
General body repairs, exterior - Edition 06.2017
2.3
Assembly overview - door handle and door lock
Note
The illustrations show the left-hand side. The procedure for the right-hand side is basically the same.
1 - Door handle
❑ Removing and installing
⇒ page 139
2 - Bolt
❑ 1.5 Nm
❑ Bearing plate is loos‐
ened from door when
this bolt is loosened
3 - Bearing bracket
❑ Removing and installing
⇒ page 143
4 - Bowden cable
❑ From door lock -1- to
door handle bracket -3-
5 - Bowden cable
❑ From inner door handle
to door lock -1-
❑ With grommet to pas‐
sage on cover.
6 - Bolt
❑ Qty. 2
❑ 18 Nm
Note
The bolts are microenca
and must be renewed e
they are unscrewed.
7 - Door lock
❑ Removing and installing
⇒ page 145
8 - Bolt
❑ 3 Nm
❑ For lock cylinder.
9 - Lock cylinder
❑ Removing and installing ⇒ page 135
❑ Only installed on driver door.
10 - Carrier
11 - Cover
❑ Removing and installing ⇒ page 130
120
Rep. gr.57 - Front doors, door components, central locking
2024 VW Tiguan Owner's Manual
