VW Tiguan Service & Owner's Manuals
 Download
Table of Contents > Exterior equipment > Mouldings, trims, extensions

VW Tiguan Body Repairs Exterior ➜ Mouldings, trims, extensions

Tiguan 2016 ➀ , Tiguan RUS 2017 ➀  
General body repairs, exterior - Edition 06.2017  
3
Mouldings, trims, extensions  
β‡’ β€œ3.1 Assembly overview - water deflector”, page 352  
β‡’ β€œ3.2 Assembly overview - wheel arch covers”, page 354  
β‡’ β€œ3.3 Assembly overview - heat shield”, page 355  
lk  
β‡’ β€œ3.4 Removing and installing water deflector”, page 356  
β‡’ β€œ3.5 Removing and installing cover”, page 357  
β‡’ β€œ3.6 Removing and installing B-pillar trim on door”, page 363  
β‡’ β€œ3.7 Removing and installing trim strip”, page 365  
β‡’ β€œ3.8 Removing and installing entry moulding”, page 367  
β‡’ β€œ3.9 Removing and installing wheel arch covers”, page 370  
β‡’ β€œ3.10 Removing and installing underbody heat shield”,  
page 377  
3.1  
Assembly overview - water deflector  
Note  
The right side is shown. The left side is similar.  
352  
Rep. gr.66 - Exterior equipment  
theMANUALS.org  
 
Tiguan 2016 ➀ , Tiguan RUS 2017 ➀  
General body repairs, exterior - Edition 06.2017  
1 - Water deflector  
❑ Removing and installing  
β‡’ page 356  
2 - Retaining strip  
–
During removal, drill out  
rivet heads and chop  
through rivet shanks.  
3 - A-pillar  
4 - Pop rivet  
❑ Qty. 5  
❑ Insert with pop rivet pli‐  
ers - VAS 5072-  
5 - Clip  
❑ Position clip in wing hole  
and press forwards, af‐  
terwards turn through  
90Β°.  
6 - Wings  
3. Mouldings, trims, extensions  
353  
theMANUALS.org  
Tiguan 2016 ➀ , Tiguan RUS 2017 ➀  
General body repairs, exterior - Edition 06.2017  
3.2  
Assembly overview - wheel arch covers  
Note  
♦ The illustrations show the left-hand side. The right side is analogous.  
♦ Different versions depending on model version; for allocation refer to β‡’ Electronic parts catalogue ETKA  
1 - Front wheel arch cover  
❑ Removing and installing  
β‡’ page 370  
2 - Double-sided adhesive  
tape  
3 - Wheel housing trim  
❑ Removing and installing  
β‡’ page 370  
4 - Bolts  
❑ Qty. 3  
❑ 2 Nm  
5 - Clip  
❑ Qty. 8  
6 - Grommets  
❑ Qty. 8 at front and rear  
7 - Rear wheel arch cover  
❑ Removing and installing  
β‡’ page 370  
8 - Clip  
❑ Qty. 8  
9 - Bolts  
❑ Qty. 2  
❑ 2 Nm  
354  
Rep. gr.66 - Exterior equipment  
theMANUALS.org  
Tiguan 2016 ➀ , Tiguan RUS 2017 ➀  
General body repairs, exterior - Edition 06.2017  
3.3  
Assembly overview - heat shield  
lk  
1 - Underbody heat shield  
❑ Removing and installing  
β‡’ page 377  
2 - Clamping washer  
❑ Qty. 6  
3 - Heat shield for centre ex‐  
haust system  
❑ Removing and installing  
β‡’ page 378  
4 - Clamping washer  
❑ Qty. 2  
5 - Heat shield for rear silencer  
❑ Removing and installing  
β‡’ page 379  
6 - Clamping washer  
❑ Qty. 5  
3. Mouldings, trims, extensions  
355  
theMANUALS.org  
Tiguan 2016 ➀ , Tiguan RUS 2017 ➀  
General body repairs, exterior - Edition 06.2017  
3.4  
Removing and installing water deflector  
Note  
Removal and installation are described only for the left side. Removal and installation of the right side are  
similar.  
Removing  
– Starting at bottom end, pull water deflector -1- out of clip -3-  
and retaining strip -2-.  
Installing  
– Position upper inner edge of water deflector -1- on upper edge  
of windscreen.  
– Press water deflector -1- from above into retaining strip -2- and  
clip -3-.  
– Fit contact lip between water deflector and windscreen behind  
window.  
356  
Rep. gr.66 - Exterior equipment  
theMANUALS.org  
Tiguan 2016 ➀ , Tiguan RUS 2017 ➀  
General body repairs, exterior - Edition 06.2017  
3.5  
Removing and installing cover  
β‡’ β€œ3.5.2 Removing and installing front door cover”, page 357  
β‡’ β€œ3.5.3 Removing and installing rear door cover”, page 360  
3.5.1  
Fitting instructions  
Special tools and workshop equipment required  
♦ Adhesive strip remover - VAS 6349-  
♦ Covers or chrome strips in covers cannot be removed intact.  
Various versions, for allocation see β‡’ Electronic parts cata‐  
logue (ETKA) .  
♦ If a cover is installed for the first time on a new vehicle or on  
newly painted surfaces, the procedure in β‡’ Workshop manual  
β€œPaint”; β‡’ Paintwork repairs; β‡’ Paint finish; β‡’ Mouldings & film  
should be observed.  
♦ If a cover is removed and reinstalled, use only adhesivelkre‐  
mover to remove the adhesive residue in the installation area.  
♦ Remove existing adhesive residue of adhesive tape using ad‐  
hesive strip remover - VAS 6349- .  
♦ Ensure that the adhesive surfaces are free of dust and grease.  
♦ The cover must be bonded in place immediately following  
cleaning.  
♦ Remove protective film immediately before installation.  
♦ Working temperature is approx. 21 Β°C.  
3.5.2  
Removing and installing front door cover  
Special tools and workshop equipment required  
♦ Torque wrench - V.A.G 1783-  
3. Mouldings, trims, extensions  
357  
theMANUALS.org  
 
Tiguan 2016 ➀ , Tiguan RUS 2017 ➀  
General body repairs, exterior - Edition 06.2017  
♦ Hot-air blower - V.A.G 1416-  
358  
Rep. gr.66 - Exterior equipment  
theMANUALS.org  
lk  
Tiguan 2016 ➀ , Tiguan RUS 2017 ➀  
General body repairs, exterior - Edition 06.2017  
Removing  
Note  
♦ The removal and installation procedures for front door cover may have to be revised slightly depending on  
model variations.  
♦ The removal and installation sequence is for the front left door cover only. Removal and installation of the  
front door cover on the right are similar.  
– Unscrew bolts -5- on inner side of door -4-.  
– Heat up cover in area of bonding surfaces -6- using hot air  
blower - V.A.G 1416- .  
– Pull off cover -1- from door until bond of adhesive tape is re‐  
leased.  
– Pull cover further out of grommets -2- -arrows a-.  
– Pull cover -1- downwards -arrows b- from door.  
Installing  
Install in reverse order, noting the following:  
3. Mouldings, trims, extensions  
359  
theMANUALS.org  
lk  
Tiguan 2016 ➀ , Tiguan RUS 2017 ➀  
General body repairs, exterior - Edition 06.2017  
Follow installation instructions β‡’ page 357 .  
– Check grommets -3- and clips -2- for damage, and renew them  
if necessary.  
– Push cover -1- from below onto door -4- -arrows a-.  
– Press cover -1- with clips -2- into grommets -3- -arrows b-.  
– Pull off protective film -6- from adhesive tape -7-.  
– Press on cover -1- forcefully in area of adhesive tape sections  
-7-.  
– Tighten bolts -5- on inner side of door.  
Specified torques  
Component  
Specified torque  
2 Nm  
Front door moulding  
3.5.3  
Removing and installing rear door cover  
Special tools and workshop equipment required  
♦ Torque wrench - V.A.G 1783-  
♦ Hot-air blower - V.A.G 1416-  
360  
Rep. gr.66 - Exterior equipment  
theMANUALS.org  
Tiguan 2016 ➀ , Tiguan RUS 2017 ➀  
General body repairs, exterior - Edition 06.2017  
Removing  
Note  
♦ The removal and installation procedures for rear door cover may have to be revised slightly depending on  
model variations.  
♦ The removal and installation sequence is for the rear left door cover only. Removal and installation of the  
rear door cover on the right are similar.  
– Unscrew bolts -5- on inner side of door -4-.  
– Heat up cover in area of bonding surfaces -6- using hot air  
blower - V.A.G 1416- .  
– Pull off cover -1- from door until bond of adhesive tape is re‐  
leased.  
– Pull cover -1- out of grommets -2- -arrows a-.  
– Pull cover -1- downwards -arrows b- from door.  
3. Mouldings, trims, extensions  
361  
theMANUALS.org  
Tiguan 2016 ➀ , Tiguan RUS 2017 ➀  
General body repairs, exterior - Edition 06.2017  
Installing  
Install in reverse order, noting the following:  
Follow installation instructions β‡’ page 357 .  
– Check grommets -3- and clips -2- for damage, and renew them  
if necessary.  
– Push cover -1- from below onto door -5- -arrows a-.  
– Press cover -1- with clips -2- into grommets -3- -arrows b-.  
– Pull off protective film -6- from adhesive tape -7-.  
– Press on cover -1- forcefully in area of adhesive tape sections  
-7-.  
– Tighten bolts -4- on inner side of door.  
Specified torques  
Component  
Specified torque  
2 Nm  
Rear door moulding  
362  
Rep. gr.66 - Exterior equipment  
theMANUALS.org  
Tiguan 2016 ➀ , Tiguan RUS 2017 ➀  
General body repairs, exterior - Edition 06.2017  
3.6  
Removing and installing B-pillar trim on  
door  
lk  
β‡’ β€œ3.6.1 Removing and installing B-pillar trim on front door”, page  
363  
β‡’ β€œ3.6.2 Removing and installing B-pillar trim on rear door”, page  
364  
3.6.1  
Removing and installing B-pillar trim on front door  
Note  
Removal and installation are described only for the left side. Removal and installation of the right side are  
similar.  
Removing  
– Run door window down to bottom position.  
– Pull window channel -3- in area of B-pillar trim-1- out of door  
frame.  
– Unclip spreader rivets -2-.  
3. Mouldings, trims, extensions  
363  
theMANUALS.org  
 
Tiguan 2016 ➀ , Tiguan RUS 2017 ➀  
General body repairs, exterior - Edition 06.2017  
– Push B-pillar trim -1- downwards and pull off door frame.  
– Pull out B-pillar trim -1- upwards.  
Installing  
– Position B-pillar trim -1- on door frame.  
– Guide in B-pillar trim -1- at bottom and fit it in place.  
– Push B-pillar trim -1- upwards until it is in contact with window  
channel -3-.  
– Hook in spreader rivet -2- from top to bottom and insert window  
channel -3- into B-pillar trim.  
3.6.2  
Removing and installing B-pillar trim on relak r door  
Note  
Removal and installation are described only for the left side. Removal and installation of the right side are  
similar.  
Removing  
– Run door window down to bottom position.  
364  
Rep. gr.66 - Exterior equipment  
theMANUALS.org  
Tiguan 2016 ➀ , Tiguan RUS 2017 ➀  
General body repairs, exterior - Edition 06.2017  
– Pull window channel -3- in area of B-pillar trim-1- out of door  
frame.  
– Unclip spreader rivets -2-.  
– Push B-pillar trim -1- downwards and pull off door frame.  
– Pull out B-pillar trim -1- upwards.  
Installing  
– Insert B-pillar trim -1- on door frame.  
– Fit B-pillar trim -1- in longitudinal holes -4- in frame section.  
– Position B-pillar trim -1- and push until stop.  
lk  
– Push B-pillar trim -1- upwards until it is in contact with window  
channel -3-.  
– Hook in spreader rivet -2- from top to bottom and insert window  
channel -3- into B-pillar trim.  
3.7  
Removing and installing trim strip  
β‡’ β€œ3.7.1 Removing and installing window channel trim strip of front  
door”, page 365  
β‡’ β€œ3.7.2 Removing and installing window channel trim strip of rear  
door”, page 367  
3.7.1  
Removing and installing window channel trim strip of front door  
3. Mouldings, trims, extensions  
365  
theMANUALS.org  
 
Tiguan 2016 ➀ , Tiguan RUS 2017 ➀  
General body repairs, exterior - Edition 06.2017  
Removing  
– Detach trim strip -1- from clips -3-, and pull it out of window  
channel -2-.  
Installing  
– Push trim strip -1- into window channel -2- until window chan‐  
nel engages in clips -3-.  
366  
Rep. gr.66 - Exterior equipment  
theMANUALS.org  
Tiguan 2016 ➀ , Tiguan RUS 2017 ➀  
General body repairlsk, exterior - Edition 06.2017  
3.7.2  
Removing and installing window channel trim strip of rear door  
Removing  
– Detach trim strip -1- from clips -3-, and pull it out of window  
channel -2-.  
Installing  
– Push trim strip -1- into window channel -2- until window chan‐  
nel engages in clips -3-.  
3.8  
Removing and installing entry moulding  
β‡’ β€œ3.8.1 Fitting instructions”, page 367  
β‡’ β€œ3.8.2 Removing and installing outer sill panel trim”,  
page 368  
3.8.1  
Fitting instructions  
Special tools and workshop equipment required  
3. Mouldings, trims, extensions  
367  
theMANUALS.org  
 
Tiguan 2016 ➀ , Tiguan RUS 2017 ➀  
General body repairs, exterior - Edition 06.2017  
♦ Adhesive strip remover - VAS 6349-  
♦ If a sill panel trim is installed for the first time on a new vehicle  
or on newly painted surfaces, the procedure in β‡’ Workshop  
manual β€œPaint”; β‡’ Paintwork repairs; β‡’ Paint finish; β‡’ Mould‐  
ings & film should be observed.  
♦ If the sill panel trim is removed and reinstalled, only use ad‐  
hesive remover to remove the adhesive remains in installation  
area.  
♦ Remove existing adhesive residue of adhesive tape using ad‐  
hesive strip remover - VAS 6349- .  
♦ Ensure that the adhesive surfaces are free of dust and grease.  
♦ The sill panel trim must be bonded in place immediately after  
cleaning.  
♦ Remove protective film immediately before installation.  
♦ Working temperature is approx. 21 Β°C.  
3.8.2  
Removing and installing outer sill panel  
trim  
Special tools and workshop equipment required  
♦ Hot-air blower - V.A.G 1416-  
368  
Rep. gr.66 - Exterior equipment  
theMANUALS.org  
Tiguan 2016 ➀ , Tiguan RUS 2017 ➀  
General body repairs, exterior - Edition 06.2017  
Removing  
Note  
♦ Sill panel trim cannot be removed without being damaged.  
♦ Different versions depending on model version; for allocation refer to β‡’ Electronic parts catalogue ETKA  
♦ Removal and installation are described only for the left side. Removal and installation of the right side are  
similar.  
– Heat sill panel trim -1- using hot air blower - V.A.G 1416- , and  
pull it off sill.  
Installing  
Install in reverse order, noting the following:  
– Installation notes β‡’ page 367 .  
– Pull off backing.  
– Align front end of outer sill panel trim -1- with front end of inner  
sill panel trim -arrows-.  
3. Mouldings, trims, extensions  
369  
theMANUALS.org