Download
Table of Contents > Passenger protection > Pedestrian protection

VW Tiguan Body Repairs Interior ➜ Pedestrian protection

Tiguan 2016 ➤ , Tiguan RUS 2017 ➤  
General body repairs, interior - Edition 03.2017  
lk  
12  
Pedestrian protection  
⇒ “12.2 Removing and installing centre crash sensor for pedes‐  
trian protection G693 ”, page 143  
⇒ “12.3 Removing and installing crash sensor for pedestrian pro‐  
tection”, page 145  
⇒ “12.4 Removing and installing trigger for pedestrian protection  
G598 / G599 ”, page 146  
⇒ “12.5 Remove and installing front pressure hose sensor for pe‐  
destrian protection G579 ”, page 150  
12.1  
Assembly overview - pedestrian protection  
1 - Clip  
2 - Trigger 1 for pedestrian pro‐  
tection - G598-  
❑ Resetting triggered pe‐  
destrian protection ⇒  
General body repairs,  
exterior; Rep. gr. 55 ;  
Bonnet; Assembly over‐  
view - bonnet  
❑ Removing and installing  
⇒ page 146  
3 - Nut  
❑ 8 Nm  
4 - Centre crash sensor for pe‐  
destrian protection - G693-  
❑ Fitting location: on  
bumper cover  
❑ Removing and installing  
⇒ page 143  
❑ Must always be re‐  
newed if:  
♦ Moulded foam insert visibly  
damaged  
♦ Impact bar visibly deformed  
♦ Bumper cover deformed  
5 - Bolt  
❑ 6 Nm  
6 - Bolt  
❑ 6 Nm  
7 - Driver side crash sensor for  
pedestrian protection - G570-  
❑ Fitting location: on bumper cover  
❑ Removing and installing ⇒ page 145  
❑ Must always be renewed if:  
♦ Foam visibly damaged  
♦ Impact bar visibly deformed  
♦ Bumper cover deformed  
142  
Rep. gr.69 - Passenger protection  
theMANUALS.org  
 
Tiguan 2016 ➤ , Tiguan RUS 2017 ➤  
General body repairs, interior - Edition 03.2017  
8 - Driver side crash sensor 2 for pedestrian protection - G851-  
❑ Part of front pressure hose sensor for pedestrian protection - G579-  
9 - Front pressure hose sensor for pedestrian protection - G579-  
❑ Fitting location: in moulded foam element on impact bar  
❑ Must always be renewed if:  
♦ Moulded foam element is visibly damaged  
♦ Impact bar visibly deformed  
♦ Bumper cover deformed  
♦ Pressure hose damaged  
❑ Insert pressure hose in groove of moulded foam element  
❑ Insert pressure hose in moulded foam element, excessive should be routed in compensation zones  
without kinks  
❑ Do not kink or crimp pressure hose  
❑ Removing and installing ⇒ page 150  
lk  
10 - Front passenger side crash sensor 2 for pedestrian protection - G852-  
❑ Part of front pressure hose sensor for pedestrian protection - G579-  
11 - Front passenger side crash sensor for pedestrian protection - G571-  
❑ Fitting location: on bumper cover  
❑ Removing and installing ⇒ page 145  
❑ Must always be renewed if:  
♦ Foam visibly damaged  
♦ Impact bar visibly deformed  
♦ Bumper cover deformed  
12 - Bolt  
❑ 6 Nm  
13 - Nut  
❑ 8 Nm  
14 - Trigger 2 for pedestrian protection - G599-  
❑ Resetting triggered pedestrian protection ⇒ General body repairs, exterior; Rep. gr. 55 ; Bonnet; As‐  
sembly overview - bonnet  
❑ Removing and installing ⇒ page 146  
15 - Clip  
12.2  
Removing and installing centre crash  
sensor for pedestrian protection - G693-  
Removing  
– Disconnect battery earth cable with ignition switched on ⇒  
Electrical system; Rep. gr. 27 ; Battery; Connecting and dis‐  
connecting battery .  
– Remove bumper cover ⇒ General body repairs, exterior; Rep.  
gr. 63 ; Front bumper; Removing and installing bumper cover .  
12. Pedestrian protection  
143  
theMANUALS.org  
lk  
Tiguan 2016 ➤ , Tiguan RUS 2017 ➤  
General body repairs, interior - Edition 03.2017  
– Unscrew bolt -2- and remove centre crash sensor for pedes‐  
trian protection - G693- -item 3- from bumper.  
WARNING  
Risk of injury due to unintentional triggering!  
♦ Before handling pyrotechnic components (e.g. separating  
the electrical connector), the person handling them must  
ensure that he/she is “electrically discharged”. To do this  
briefly touch, for example, the door striker plate.  
– Separate electrical connector -1- while holding down connec‐  
tor locking mechanism.  
Installing  
WARNING  
♦ Observe safety precautions when working on pyrotechnic  
components ⇒ page 3 .  
♦ Before handling pyrotechnic components (e.g. connecting  
the electrical connector), the person handling them must  
ensure that he/she is “electrically discharged”. To do this  
briefly touch, for example, the door striker plate.  
– Fit connector to crash sensor until it engages audibly.  
Continue installation in reverse order of removal observing the  
following:  
Note  
Ensure that the electrical connectors are pushed fully onto  
stop and engage audibly.  
Ensure that no wires are trapped.  
WARNING  
Risk of accidental triggering after incorrect repair of pyrotech‐  
nical components (for example airbag, belt tensioner) when  
battery is connected.  
♦ Battery must be connected with ignition switched on.  
♦ For your own safety, stay out of the airbag deployment  
areas when connecting the battery and keep a safe dis‐  
tance away from the belt tensioners/belts.  
♦ Ensure, at the time of connecting the battery, that no other  
persons are inside the vehicle.  
– Connect battery earth cable with ignition switched on ⇒ Elec‐  
trical system; Rep. gr. 27 ; Battery; Connecting and discon‐  
necting battery .  
144  
Rep. gr.69 - Passenger protection  
theMANUALS.org  
Tiguan 2016 ➤ , Tiguan RUS 2017 ➤  
General body repairs, interior - Edition 03.2017  
lk  
Note  
If airbag warning lamp - K75- indicates a fault following installa‐  
tion, event memory must be read, deleted and read again ⇒ Ve‐  
hicle diagnostic tester.  
Installation tips: for example tightening torques, renewing com‐  
ponents  
⇒ “12.1 Assembly overview - pedestrian protection”, page 142  
12.3  
Removing and installing crash sensor  
for pedestrian protection  
Removing  
– Disconnect battery earth cable with ignition switched on ⇒  
Electrical system; Rep. gr. 27 ; Battery; Connecting and dis‐  
connecting battery .  
– Remove bumper cover ⇒ General body repairs, exterior; Rep.  
gr. 63 ; Front bumper; Removing and installing bumper cover .  
– Unscrew bolt -3- and remove driver side crash sensor for pe‐  
destrian protection - G570- / front passenger side crash sensor  
for pedestrian protection - G571- -1- from bumper.  
– Disconnect electrical connector -2-.  
WARNING  
Before handling pyrotechnic components (e.g. separating the  
electrical connector), the person handling them must ensure  
that he/she is “electrically discharged”. To do this briefly touch,  
for example, the door striker plate.  
– Pull out connector lock -2-, press it down -arrow- and discon‐  
nect connector -1- on crash sensor.  
Installing  
WARNING  
♦ Observe safety precautions when working on pyrotechnic  
components ⇒ page 3 .  
♦ Before handling pyrotechnic components (e.g. connecting  
the electrical connector), the person handling them must  
ensure that he/she is “electrically discharged”. To do this  
briefly touch, for example, the door striker plate.  
12. Pedestrian protection  
145  
theMANUALS.org