Arteon 2018 ➤, Arteon 2021 ➤, Arteon Shooting Brake 2021 ➤, Golf 2013 ➤, Golf 2 ...
4-cyl. direct injection engine (1.8 l and 2.0 l, 4 V, EA 888 gen III, turbocharger, chain drive) - Edition
02.2021
3
Coolant pipes
⇒ a3.3 nd installing upper coolant pipes”, page 345
3.1
Assembly overview - coolant pipes
1 - Coolant pipe
❑ On top of engine
❑ Removing and instal‐
ling ⇒ page 345
2 - Bolts
❑ 9 Nm
3 - Bolts
❑ 9 Nm
4 - Coolant line
5 - Bolts
❑ 9 Nm
6 - Coolant pipe
❑ to radiator cowl
❑ Only for vehicles with
auxiliary radiator
7 - Coolant pipe
❑ On front of engine
❑ Removing and instal‐
ling ⇒ page 343
8 - Bolts
❑ 6 Nm
3.2
Removing and installing coolant pipes
3.2.1
Removing and installing front coolant
pipe
Special tools and workshop equipment required
3. Coolant pipes
343
Arteon 2018 ➤, Arteon 2021 ➤, Arteon Shooting Brake 2021 ➤, Golf 2013 ➤, Golf 2 ...
4-cyl. direct injection engine (1.8 l and 2.0 l, 4 V, EA 888 gen III, turbocharger, chain drive) - Edition
02.2021
♦ Hose clamps to 25 mm -3094-
♦ Spring-type clip pliers -VAS 6362-
Removing
– Remove air filter housing ⇒ page 443 .
– Unscrew bolt -arrow- on left and right.
– Unclip lower part of air duct -1- and remove it.
344
Rep. gr.19 - Cooling
Arteon 2018 ➤, Arteon 2021 ➤, Arteon Shooting Brake 2021 ➤, Golf 2013 ➤, Golf 2 ...
4-cyl. direct injection engine (1.8 l and 2.0 l, 4 V, EA 888 gen III, turbocharger, chain drive) - Edition
02.2021
Note
Use a cloth to catch the escaping coolant.
– Clamp off coolant hoses -1 and 2- with hose clamps, up to
25 mm in diameter -3094-.
– Release hose clips and detach coolant hoses.
– Unscrew bolts -arrows- and remove front coolant pipe.
Installing
Install in reverse order of removal, observing the following:
Note
Secure all hose connections with the correct type of hose clips
(same as original equipment) ⇒ Electronic parts catalogue (ET‐
KA).
– Check coolant level and top up as needed ⇒ page 286 .
Specified torques
♦ ⇒ o3.1 verview - coolant pipes”, page 343
3.3
Removing and installing upper coolant
pipes
Special tools and workshop equipment required
♦ Hose clamps to 25 mm -3094-
3. Coolant pipes
345
Arteon 2018 ➤, Arteon 2021 ➤, Arteon Shooting Brake 2021 ➤, Golf 2013 ➤, Golf 2 ...
4-cyl. direct injection engine (1.8 l and 2.0 l, 4 V, EA 888 gen III, turbocharger, chain drive) - Edition
02.2021
♦ Spring-type clip pliers -VAS 6362-
Removing
– Remove Ignition coil with output stage for cylinder “3” ⇒
page 580 .
– Release fasteners -arrows- and detach wiring duct -1- from
bracket.
– Clamp off coolant hoses before and after coolant pipe using
hose clamps up to 25 mm -3094-.
– Release hose clips -arrows- and detach coolant hoses.
– Unscrew bolt -1- and remove coolant pipe (top).
Installing
Install in reverse order of removal, observing the following:
346
Rep. gr.19 - Cooling