Arteon 2018 ➤, Arteon 2021 ➤, Arteon Shooting Brake 2021 ➤, Golf 2013 ➤, Golf 2 ...
4-cyl. direct injection engine (1.8 l and 2.0 l, 4 V, EA 888 gen III, turbocharger, chain drive) - Edition
02.2021
2
Engine oil cooler
2.1
Assembly overview - engine oil cooler
1 - Ancillary bracket
❑ Removing and instal‐
ling ⇒ page 95
2 - Seal
❑ Renew
3 - O-ring
❑ Renew if damaged
❑ Moisten with engine oil
4 - Mechanical switching
valve
❑ Removing and instal‐
ling ⇒ page 253
5 - Engine oil cooler
❑ Observe notes ⇒ page
232
❑ Removing and instal‐
ling ⇒ page 251
6 - Seal
❑ Renew
❑ Moisten with coolant
7 - Connection
8 - Bolt
❑ Renew
❑ 8 Nm +45°
2.2
Removing and installing engine oil
cooler
Special tools and workshop equipment required
2. Engine oil cooler
251
Arteon 2018 ➤, Arteon 2021 ➤, Arteon Shooting Brake 2021 ➤, Golf 2013 ➤, Golf 2 ...
4-cyl. direct injection engine (1.8 l and 2.0 l, 4 V, EA 888 gen III, turbocharger, chain drive) - Edition
02.2021
♦ Drip tray for workshop hoist -VAS 6208-
Removing
CAUTION
The cooling system could be under pressure. Hot steam/hot
coolant can escape - risk of scalding.
Skin and other parts of the body may be scalded.
– Wear protective gloves.
– Wear protective goggles.
– Reduce excess pressure by covering cap of coolant ex‐
pansion tank with suitable cloth and opening it carefully.
– Drain coolant ⇒ page 278 .
– Remove bracket for ancillaries ⇒ page 95 .
– Unscrew bolts -4 and 5- and remove engine oil cooler -3-
together with seal -2-.
Installing
Install in reverse order of removal, observing the following:
Note
♦ Renew gaskets and seals.
♦ Secure all hose connections with the correct type of hose
clips (same as original equipment) ⇒ Electronic parts cata‐
logue (ETKA).
– Install engine oil cooler -3- with new seal -2-.
252
Rep. gr.17 - Lubrication
Arteon 2018 ➤, Arteon 2021 ➤, Arteon Shooting Brake 2021 ➤, Golf 2013 ➤, Golf 2 ...
4-cyl. direct injection engine (1.8 l and 2.0 l, 4 V, EA 888 gen III, turbocharger, chain drive) - Edition
02.2021
– Install bracket for ancillaries ⇒ page 95 .
– Add coolant ⇒ page 282 .
– Replenish engine oil and check oil level ⇒ Maintenance;
Booklet ; Engine oil: Draining; Renewing oil filter and replen‐
ishing engine oil.
Specified torques
♦ ⇒ o2.1 verview - engine oil cooler”, page 251
Removing and installing mechanical switching valve
Removing
– Remove engine oil cooler ⇒ page 251 .
– Remove mechanical switching valve -1- from ancillary brack‐
et -arrow-.
Installing
Install in reverse order of removal, observing the following:
Note
♦ Renew O-rings if damaged.
♦ Secure all hose connections with the correct type of hose
clips (same as original equipment) ⇒ Electronic parts cata‐
logue (ETKA).
– Moisten O-rings of mechanical switching valve with engine
oil, and install switching valve.
– Install engine oil cooler ⇒ page 251 .
2. Engine oil cooler
253
2024 VW Tiguan Owner's Manual
