Arteon 2018 ➤, Arteon 2021 ➤, Arteon Shooting Brake 2021 ➤, Golf 2013 ➤, Golf 2 ...
4-cyl. direct injection engine (1.8 l and 2.0 l, 4 V, EA 888 gen III, turbocharger, chain drive) - Edition
02.2021
8
Lambda probe
⇒ a8.2.1 nd installing Lambda probe 1 before catalytic conver‐
terGX10”, page 497
⇒ a8.2.2 nd installing Lambda probe 1 after catalytic conver‐
terGX7”, page 499
8.1
Assembly overview - Lambda probe
Lambda probe connectors
♦ 5-pin connector for lambda probe 1 before catalytic convert‐
er -GX10-
♦ 4-pin connector for lambda probe 1 after catalytic converter
-GX7-
Note
♦ New lambda probes are coated with an assembly paste.
This paste must not get into the slots on the Lambda probe
body.
♦ In the case of a used Lambda probe, grease only the thread
with high-temperature paste. This paste must not get into the
slots on the Lambda probe body. High-temperature paste
⇒ Electronic parts catalogue (ETKA)
♦ During installation, it is essential that wiring of lambda probe
is reattached in same positions. The wire must be prevented
from touching the exhaust pipe.
496
Rep. gr.24 - Mixture preparation - injection
Arteon 2018 ➤, Arteon 2021 ➤, Arteon Shooting Brake 2021 ➤, Golf 2013 ➤, Golf 2 ...
4-cyl. direct injection engine (1.8 l and 2.0 l, 4 V, EA 888 gen III, turbocharger, chain drive) - Edition
02.2021
1 - Lambda probe 1 after cat‐
alytic converter -GX7-
❑ Consisting of:
Lambda probe after cat‐
alytic converter -G130-
Lambda probe 1 heater
after catalytic converter
-Z29-
❑ Specified torque:
55 Nm
❑ ⇒ a8.2.2 nd instal‐
ling Lambda probe 1
after catalytic conver‐
terGX7”, page 499
2 - Lambda probe 1 before
catalytic converter -GX10-
❑ Consisting of:
Lambda probe -G39-
Lambda probe heater -
Z19-
❑ Specified torque:
55 Nm
8.2
Removing and installing Lambda probe
⇒ a8.2.2 nd installing Lambda probe 1 after catalytic conver‐
terGX7”, page 499
8.2.1
Removing and installing Lambda probe
1 before catalytic converter -GX10-
Lambda probe 1 before catalytic converter -GX10- consists of
♦ Lambda probe -G39-
♦ Lambda probe heater -Z19-
Special tools and workshop equipment required
8. Lambda probe
497
Arteon 2018 ➤, Arteon 2021 ➤, Arteon Shooting Brake 2021 ➤, Golf 2013 ➤, Golf 2 ...
4-cyl. direct injection engine (1.8 l and 2.0 l, 4 V, EA 888 gen III, turbocharger, chain drive) - Edition
02.2021
♦ Lambda probe open ring spanner set -3337-
Removing
– Separate 5-pin connector for lambda probe 1 before catalytic
converter -GX10-.
– Unscrew Lambda probe 1 before catalytic converter -GX10-
-1- using tool from Lambda probe open ring spanner set
-3337-.
Installing
When installing, note the following:
498
Rep. gr.24 - Mixture preparation - injection
Arteon 2018 ➤, Arteon 2021 ➤, Arteon Shooting Brake 2021 ➤, Golf 2013 ➤, Golf 2 ...
4-cyl. direct injection engine (1.8 l and 2.0 l, 4 V, EA 888 gen III, turbocharger, chain drive) - Edition
02.2021
Note
♦ New lambda probes are coated with an assembly paste.
This paste must not get into the slots on the Lambda probe
body.
♦ In the case of a used Lambda probe, grease only the thread
with high-temperature paste. This paste must not get into the
slots on the Lambda probe body. High-temperature paste
⇒ Electronic parts catalogue (ETKA).
♦ During installation, it is essential that wiring of lambda probe
is reattached in same positions. The wire must be prevented
from touching the exhaust pipe.
Specified torques
♦ ⇒ o8.1 verview - Lambda probe”, page 496
8.2.2
Removing and installing Lambda probe
1 after catalytic converter -GX7-
Lambda probe 1 after catalytic converter -GX7- consists of
♦ Lambda probe after catalytic converter -G130-
♦ Lambda probe 1 heater after catalytic converter -Z29-
Special tools and workshop equipment required
♦ Lambda probe open ring spanner set -3337-
Removing
– Separate 4-pin connector for lambda probe 1 after catalytic
converter -GX7-.
– Unscrew Lambda probe -1-, using tool from Lambda probe
open ring spanner set -3337-.
8. Lambda probe
499
Arteon 2018 ➤, Arteon 2021 ➤, Arteon Shooting Brake 2021 ➤, Golf 2013 ➤, Golf 2 ...
4-cyl. direct injection engine (1.8 l and 2.0 l, 4 V, EA 888 gen III, turbocharger, chain drive) - Edition
02.2021
Installing
When installing, note the following:
Note
♦ New lambda probes are coated with an assembly paste.
This paste must not get into the slots on the Lambda probe
body.
♦ In the case of a used Lambda probe, grease only the thread
with high-temperature paste. This paste must not get into the
slots on the Lambda probe body. High-temperature paste
⇒ Electronic parts catalogue (ETKA).
♦ During installation, it is essential that wiring of lambda probe
is reattached in same positions. The wire must be prevented
from touching the exhaust pipe.
Specified torques
♦ ⇒ o8.1 verview - Lambda probe”, page 496
500
Rep. gr.24 - Mixture preparation - injection
2024 VW Tiguan Owner's Manual
